my profile | my password | search | faq & rules | forum home

» Film-Tech Forum ARCHIVE   » Operations   » Film Handlers' Forum   » Scratches on Print

Author Topic: Scratches on Print Ian Bailey Master Film Handler Posts: 317 From: Nambucca Heads, Australia Registered: Jun 2003 posted 03-16-2004 08:55 PM                     I have had a few problems recently with prints showing scratches on them.One print has a fine continuous black line down the middle of the image and the other had short(yellow-green)scratches on the right hand side of the projected image.These short scratches were at a 45degree angle and appeared at a regular interval.We filmguard every print when we make it up,the only thing I can find is gritty dirt on the soundhead ruber layback roller.Would the use of filmguard cause dirt to be attracted to the rubber layback roller? Our equipment is Simplex 35(1050) projector/Simplex soundhead/Speco Platter. What is the difference between a black scratch and a yellow green scratch? What can be used to clean the rubber layback roller on the sound drum?  |  IP: Logged Daryl C. W. O'Shea Film God Posts: 3977 From: Midland Ontario Canada (where Panavision & IMAX lenses come from) Registered: Jun 2002 posted 03-16-2004 09:06 PM                        The yellow-green diagonal scratch was probably caused by either something caught on a sprocket (brush hair, etc) or by the film being scratched by the platter while building the print. Coloured scratches are on the emulsion side, that's the side towards the lamphouse, or the side facing you with the film heads up and sound track on the left. Black scratches are on the base side of the film. That'd be the side facing the screen, or the side facing you with the film heads up sound track on the right. You could probably clean the rubber with a cloth if it's got a residue of FilmGuard built up on it. If it's got crap embedded in the rubber you can try picking it out. If it's really bad you might consider replacing it.  |  IP: Logged Peter Mork Expert Film Handler Posts: 181 From: Newton, MA, USA Registered: Jun 2002 posted 03-16-2004 11:52 PM                     The sort of question that's hard to answer at a distance. Another likely culprit for those diagonal scratches is a roller going to or from the platter. If a flange drags over the emulsion side, bingo. You can sometimes tell by noting the distance between scratches what diameter the roller was that did the deed, and that can narrow down the possibilities. Any roller that swings freely on a bracket, notably the last one that feeds the film onto the platter, is especially suspect. I'm a strong advocate of gluing a disc of felt to the outside of any roller flange that MIGHT be a problem, and trimming it so it extends just a tiny bit over the flange edge. Yes, you're supposed check your lacing each run, but with thousands of runs accidents do happen, and the felt is your insurance that a mis-threaded roller won't damage the print.  |  IP: Logged William Hooper Phenomenal Film Handler Posts: 1879 From: Mobile, AL USA Registered: Jun 99 posted 03-17-2004 12:17 AM                        quote: The yellow-green diagonal scratch was probably caused by either something caught on a sprocket (brush hair, etc) or by the film being scratched by the platter while building the print. The diagonal scratches are 99% likely to be caused by making up to the platter. This runs the risk of another platter/changeover war of proselytization, but the fact is that the world knows those diagonal scratches by the name "platter scratches". Just to get the first 20 posts out of the way: blah blah blah platter scratches blah blah blah cinch marks blah blah blah platter scratches blah blah blah cinch marks blah blah blah  |  IP: Logged Michael Schaffer "Where is the Boardwalk Hotel?" Posts: 4143 From: Boston, MA Registered: Apr 2002 posted 03-17-2004 01:22 AM                        blah blah. blah blah, blah "proselytization" (!) - blah blah! blah blah blah blah. blah blah blah blah blah? blah blah...  |  IP: Logged Ian Bailey Master Film Handler Posts: 317 From: Nambucca Heads, Australia Registered: Jun 2003 posted 03-17-2004 05:08 AM                     Could I have a bit more information on what I should be looking for if the scratches were made by building the print up to the platter.  |  IP: Logged Darryl Spicer Film God Posts: 3250 From: Lexington, KY, USA Registered: Dec 2000 posted 03-17-2004 10:02 AM                    Make sure the picture area is not making contact across the surface of the platter deck. However, if you are loading the film onto the platter with the soundtrack up contact on the platter surface would have been the base side of the film not the emulsion side. I noticed that you use the Speco platter. Are you using the newer style gray makeup table or the old wooden tables. If you are using 60 min reels make sure they are in good condition and not warped causing the picture surface to come into contact with the flangs during build-up.  |  IP: Logged Daryl C. W. O'Shea Film God Posts: 3977 From: Midland Ontario Canada (where Panavision & IMAX lenses come from) Registered: Jun 2002 posted 03-17-2004 02:44 PM                        Unless of course he's got the film twisted the wrong way and low enough that it doesn't try to stand on edge, then it'd be the emulsion side. Does the diagonal line(s) repeat in the same spot every frame, or are there just lots of diagonal lines, continuously?  |  IP: Logged Patrick de Groot Expert Film Handler Posts: 161 From: Sprang-Capelle, Netherlands Registered: Apr 2001 posted 03-17-2004 02:57 PM                     quote: Coloured scratches are on the emulsion side, that's the side towards the lens, or the side facing you with the film heads up and sound track on the left. Is it not that the side opposite to the screen/lens is the emulsion side?  |  IP: Logged Daryl C. W. O'Shea Film God Posts: 3977 From: Midland Ontario Canada (where Panavision & IMAX lenses come from) Registered: Jun 2002 posted 03-17-2004 03:03 PM                        You are correct. For some reason I thought the lens was in the lamphouse last night. Probably because I had just watched a science documentary where they had the lens in the lamphouse. At least I got everything else right... including base towards the screen. Post corrected to avoid confusion.  |  IP: Logged Ian Bailey Master Film Handler Posts: 317 From: Nambucca Heads, Australia Registered: Jun 2003 posted 03-17-2004 09:08 PM                     We are using the newer style make-up table and we adjust the top roller on the MUT so the print rides onto the platter on the non-soundtrack side edge of the print.The picture area does not come in contact with the platter surface.The diagonal lines would be more than a frame apart and they appear and disappear at a constant rate,one will appear at the top of the screen and the next will be a bit lower down etc.I'd say the marks are on every second or third frame,as if it had come from a roller the size used on a platter.We have checked everything several times and the only thing we found was a small rough edge on the rubber layback roller on the sound drum.I will double check the next time we make-up a print on this gear and make sure we are not doing anything that you guys have suggested that could be causing the problem.I appreciate your comments.  |  IP: Logged Daryl C. W. O'Shea Film God Posts: 3977 From: Midland Ontario Canada (where Panavision & IMAX lenses come from) Registered: Jun 2002 posted 03-17-2004 10:16 PM                        Sounds like somebody missed a roller. Probably the roller on the lower arm of the projector. If not that one, the lower takeup roller on the platter.  |  IP: Logged William Hooper Phenomenal Film Handler Posts: 1879 From: Mobile, AL USA Registered: Jun 99 posted 03-18-2004 01:48 AM                        You literally have to find it like finding a piece in a jigsaw puzzle. The 'missing piece' is that spot on the film where it's scratched. Identify which side the scratch is on, makeup or thread up as usual, & look along the path of the film for where it is contacted on that side at that spot.  |  IP: Logged Demetris Thoupis Phenomenal Film Handler Posts: 1240 From: Aradippou, Larnaca, Cyprus Registered: Apr 2001 posted 03-18-2004 03:13 AM                     The first thing you should do is check the roller path from the platter to the projector and then back again. The film has to be passing through the rollers exactly in the middle. Try cleaning the rollers first and make sure they are turning. If the rollers are not turning then the film might be scratched on them and that might be the result of your black line. Also check the gate of the projector. Is there any dirt? The best thing is to dissasemble it, clean it well and then put it back in. Some might dissagree but put WD40 on the base of every roller that is not turning. Make sure that your gate is not too tight as well. Also check the levelling of the platter. If it is bend and the film rubs hard on it while it returns on the platter then you have a problem. Hope this could help. Demetris [ 03-18-2004, 06:36 AM: Message edited by: Demetris Thoupis ]  |  IP: Logged John Pytlak Film God Posts: 9987 From: Rochester, NY 14650-1922 Registered: Jan 2000 posted 03-18-2004 05:42 AM                        For 35mm prints, the film's emulsion side faces the lamphouse. A camera negative is exposed with the emulsion toward the camera lens. A direct print flips this orientation, so the emulsion then faces AWAY from the lens. And the normal master positive to duplicate negative duplication system maintains this orientation. The image in the gate should be upside-down, with the analog soundtrack on the outboard side of the projector. 16mm reversal camera originals (e.g., EKTACHROME or KODACHROME type films) have the emulsion facing the projector lens. 16mm prints can have either orientation.  |  IP: Logged

All times are Central (GMT -6:00)

Printer-friendly view of this topic

Hop To: Select a Forum: Category: Operations -------------------- Digital Cinema Forum Film Handlers' Forum Large Format Forum Ground Level Feature Info, Trailer Attachments & REAL Credit Offsets Category: Community -------------------- Film-Yak Film Handlers' Movie Reviews The Afterlife Bob Maar's Joke-A-Thon Category: Classified -------------------- Equipment and Supplies Wanted/For Sale Help Wanted/Seeking Employment Category: System -------------------- Software Beta Testing Forum

The Film-Tech Forums are designed for various members related to the cinema industry to express their opinions, viewpoints and testimonials on various products, services and events based upon speculation, personal knowledge and factual information through use, therefore all views represented here allow no liability upon the publishers of this web site and the owners of said views assume no liability for any ill will resulting from these postings. The posts made here are for educational as well as entertainment purposes and as such anyone viewing this portion of the website must accept these views as statements of the author of that opinion and agrees to release the authors from any and all liability.