my profile | my password | search | faq & rules | forum home

» Film-Tech Forum ARCHIVE   » Operations   » Film Handlers' Forum   » Air-Sensing switch suitable for blower failure notification

Author Topic: Air-Sensing switch suitable for blower failure notification Brad Allen Jedi Master Film Handler Posts: 688 From: Evansville, IN, USA Registered: May 2000 posted 12-26-2005 03:36 PM                     I'd like comments about using this Grainger Air Switch to alert us to the fact that a lamphouse blower fails or didn't start. I would insert the sensor into the pipe just above the lamphouse. Which would place it between the blower and the lamphouse. Comments, good, bad, ugly? I feel that maybe this is a better solution than putting a sail switch in the stack.  |  IP: Logged Mark Gulbrandsen Resident Trollmaster Posts: 16657 From: Music City Registered: Jun 99 posted 12-26-2005 04:44 PM                     That is not unlike the air pressure switch thats used in the older Christie 3/4kw lamphouses. It appears that its made to work with a positive air pressure though so inserting it in the output side of an exhaust blower would be a must. I feel that sail switches are also pretty reliable though and its pretty easy to install one in just about any lamphouse stack and wire it back in series with the safety circuit. Christie makes a sail switch update kit for their lamphouses that includes the switch, sail, bracket and hardware. It is also pretty inexpensive and very universal. Mark  |  IP: Logged Monte L Fullmer Film God Posts: 8367 From: Nampa, Idaho, USA Registered: Nov 2004 posted 12-27-2005 12:29 AM                     I've seen some places that the exhaust fan switch closed a relay - both to the fan and to the 110v to the rectifier contactor circuit. No fan on, no ignition. Wish that STRONG would have installed some better sailfin switches that goes over the blowhole that shoots the air on the cathode pin for those older X-90 consoles. Then, they got smart with the enclosed plenum for the cathode, but the muffin fan thingey for the anode pin is something else on the later X-90 consoles. -Monte [ 12-27-2005, 05:40 AM: Message edited by: Monte L Fullmer ]  |  IP: Logged Mark Gulbrandsen Resident Trollmaster Posts: 16657 From: Music City Registered: Jun 99 posted 12-27-2005 07:54 AM                     quote: Monte L Fullmer Wish that STRONG would have installed some better sailfin switches that goes over the blowhole that shoots the air on the cathode pin for those older X-90 consoles. Then, they got smart with the enclosed plenum for the cathode, but the muffin fan thingey for the anode pin is something else on the later X-90 consoles. They all work just fine if kept clean. All lamphouse blowers should be removed and the squirel cages, pipes, elbows, etc. cleaned and lubed (if needed) once a year. Blowers will last just about forever if you do this. Some blower motors need to be turned so their oil cups are facing up..... most new blowers don't have them at all.....Christie has switched to a giant all ball bearing motor in its latest console incarnation . Mark  |  IP: Logged Monte L Fullmer Film God Posts: 8367 From: Nampa, Idaho, USA Registered: Nov 2004 posted 12-27-2005 01:19 PM                     Yep, did all of that and check those inlets once a month when I visit these 32, X-90's. Boy, got that right about Christie consoles: loved that motor that sits over the plenum and even the older sleeved ones. Like a windstorm inside of those units-especially the Reference consoles with the two blowers.  |  IP: Logged Steve Scott Phenomenal Film Handler Posts: 1300 From: Minneapolis, MN Registered: Sep 2000 posted 12-28-2005 01:27 PM                     We used the original switches in question at Lakeville, and they were wired to general alarm buzzers in the ceiling near their respective groups of machines. They will certainly make management get around to fixing blower motors when the alarms go off continuously.  |  IP: Logged

All times are Central (GMT -6:00)

Printer-friendly view of this topic

Hop To: Select a Forum: Category: Operations -------------------- Digital Cinema Forum Film Handlers' Forum Large Format Forum Ground Level Feature Info, Trailer Attachments & REAL Credit Offsets Category: Community -------------------- Film-Yak Film Handlers' Movie Reviews The Afterlife Bob Maar's Joke-A-Thon Category: Classified -------------------- Equipment and Supplies Wanted/For Sale Help Wanted/Seeking Employment Category: System -------------------- Software Beta Testing Forum

The Film-Tech Forums are designed for various members related to the cinema industry to express their opinions, viewpoints and testimonials on various products, services and events based upon speculation, personal knowledge and factual information through use, therefore all views represented here allow no liability upon the publishers of this web site and the owners of said views assume no liability for any ill will resulting from these postings. The posts made here are for educational as well as entertainment purposes and as such anyone viewing this portion of the website must accept these views as statements of the author of that opinion and agrees to release the authors from any and all liability.