Tweet
I checked the history and I see that Leo had started a specific Release notes thread but I figure it would be best consolidate them into one thread. Rather than going back into the past, I'm starting with the latest release, 1.7.1. 1.7 is a major release and it touches quite a bit. It is probably worth considering for any installed systems. If you plan on HFR content when using an IMS3000 (particularly 60fps at 4K), then this version is a requirement.
Version 1.7.1 (Service release)
New feature:
• ICP-D: It’s now possible to resize HFR content (2D 48fps, 50fps, 60fps, 96fps, 100fps, 120fps and 3D 48fps, 50fps,
60fps)
Bug fixes:
• Fix an issue where the Formatter FPGA temperature where not reported in the Metrics page
Version 1.7.0 (Major release)
New feature:
• New CLO algorithm. (a new light sensor calibration is needed to activate the new algorithm)
• Support New lenses on High Contrast models (SP4K-27BHC/SP4K-13CHC, Freya, Freya+)
o R98013333 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.35-1.84
o R98013343 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.45-2.10
o R98013983 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.13-1.72
o R98013533 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.65-2.70
o R98013543 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.98-3.40
o R98529503 XLD(R) 1.38" DC4K VHC HDR 0.9-1 MAN
• ICMP: It’s now possible to resize HFR content (2D 48fps, 50fps, 60fps, 96fps, 100fps, 120fps and 3D 48fps, 50fps,
60fps)
• UI intuitiveness Improvements on several configuration pages (projector/internal clock; media server/player; Media
server automation/Devices; Color calibration/Verify corrected colors; Color calibration/Projector color)
Bug fixes:
• Fix an issue where the air inlet filter was reported to be not correctly detected
• Fix an issue where the air filter contamination sensor value was not reported on the metrics page
• Fix an issue where white point tracking curve measured in factory wasn’t save on the unit. (Unit produced with 1.7.0
will now have factory measured white point tracking curve loaded when shipped from factory).
• Fix an issue where a big brightness (increase/decrease) was visible on screen when changing CLO value while light is
off
• Fix an issue where a square picture was displayed when enabling the S4 4K/60 on IMS3000. (Creation of a new input
file or edition of the existing one is needed to fix the issue)
• Fix an issue where Engine fan is not running during the firmware component upgrade
• Improved unblanking behavior
• Fix an intermittent issue where the waking up of the projector form the Eco Page is not working.
• Fix an intermittent issue where accessing a unit after IP change (Manual <->Automatic) was not possible
• Fix an issue where the import of files with space in the filenames
• Fix an issue where the hamburger menu in Tablet mode was not clickable when the UI windows is small.
• Fix an issue where the left navigation menu on Web Communicator was disappearing when pressing escape
• Fix an issue where the bottom-right scaling values available in picture were not correct
• Fix an issue where the input cue using a Jnior was not saved correctly.
• Fix an issue where importing automation devices or user cues is not working if configuration is empty.
• Fix an issue where editing a content server in the Media server/content was not possible
• Fix an issue where deleting an ICMP/ICP-D license was not possible using Web Communicator
• Fix a scheduler issue when projector internal clock was configured with -1 as DST value.
• Fix an issue where Day and Date information on Scheduler page header cells is missing
• Fix an UI issue with the internal clock settings which switch automatically in Edit mode
• Correct some translation issue.
• Fix an issue where “access unauthorized” web page was displayed right after adding/removing user access right
Known issues:
• The air filter contamination sensor will report a wrong value right after the software update. A power cycle of the
unit is needed in order to have a correct air filter contamination value.
Version 1.7.1 (Service release)
New feature:
• ICP-D: It’s now possible to resize HFR content (2D 48fps, 50fps, 60fps, 96fps, 100fps, 120fps and 3D 48fps, 50fps,
60fps)
Bug fixes:
• Fix an issue where the Formatter FPGA temperature where not reported in the Metrics page
Version 1.7.0 (Major release)
New feature:
• New CLO algorithm. (a new light sensor calibration is needed to activate the new algorithm)
• Support New lenses on High Contrast models (SP4K-27BHC/SP4K-13CHC, Freya, Freya+)
o R98013333 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.35-1.84
o R98013343 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.45-2.10
o R98013983 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.13-1.72
o R98013533 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.65-2.70
o R98013543 MINOLTA(R) 1.38" DC4K VHC HDR 4K:1.98-3.40
o R98529503 XLD(R) 1.38" DC4K VHC HDR 0.9-1 MAN
• ICMP: It’s now possible to resize HFR content (2D 48fps, 50fps, 60fps, 96fps, 100fps, 120fps and 3D 48fps, 50fps,
60fps)
• UI intuitiveness Improvements on several configuration pages (projector/internal clock; media server/player; Media
server automation/Devices; Color calibration/Verify corrected colors; Color calibration/Projector color)
Bug fixes:
• Fix an issue where the air inlet filter was reported to be not correctly detected
• Fix an issue where the air filter contamination sensor value was not reported on the metrics page
• Fix an issue where white point tracking curve measured in factory wasn’t save on the unit. (Unit produced with 1.7.0
will now have factory measured white point tracking curve loaded when shipped from factory).
• Fix an issue where a big brightness (increase/decrease) was visible on screen when changing CLO value while light is
off
• Fix an issue where a square picture was displayed when enabling the S4 4K/60 on IMS3000. (Creation of a new input
file or edition of the existing one is needed to fix the issue)
• Fix an issue where Engine fan is not running during the firmware component upgrade
• Improved unblanking behavior
• Fix an intermittent issue where the waking up of the projector form the Eco Page is not working.
• Fix an intermittent issue where accessing a unit after IP change (Manual <->Automatic) was not possible
• Fix an issue where the import of files with space in the filenames
• Fix an issue where the hamburger menu in Tablet mode was not clickable when the UI windows is small.
• Fix an issue where the left navigation menu on Web Communicator was disappearing when pressing escape
• Fix an issue where the bottom-right scaling values available in picture were not correct
• Fix an issue where the input cue using a Jnior was not saved correctly.
• Fix an issue where importing automation devices or user cues is not working if configuration is empty.
• Fix an issue where editing a content server in the Media server/content was not possible
• Fix an issue where deleting an ICMP/ICP-D license was not possible using Web Communicator
• Fix a scheduler issue when projector internal clock was configured with -1 as DST value.
• Fix an issue where Day and Date information on Scheduler page header cells is missing
• Fix an UI issue with the internal clock settings which switch automatically in Edit mode
• Correct some translation issue.
• Fix an issue where “access unauthorized” web page was displayed right after adding/removing user access right
Known issues:
• The air filter contamination sensor will report a wrong value right after the software update. A power cycle of the
unit is needed in order to have a correct air filter contamination value.